-
Welcome to Jetboaters.net!
We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider Signing Up so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial. So what's to lose? IT IS FREE!
Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!)
Ar230 wont plane
- Thread starter Zacka4289
- Start date
- Messages
- 5,890
- Reaction score
- 6,662
- Points
- 492
- Location
- Corinth, TX (DFW)
- Boat Make
- Yamaha
- Year
- 2007
- Boat Model
- AR
- Boat Length
- 23
What does "sounding like its blowing" mean?
Are you sure you have the correct pitch impellers and there on the correct sides?
Are you sure you have the correct pitch impellers and there on the correct sides?
Acard7
Jetboaters Commander
- Messages
- 694
- Reaction score
- 1,179
- Points
- 197
- Location
- SW Iowa
- Boat Make
- Yamaha
- Year
- 2024
- Boat Model
- 252SE
- Boat Length
- 25
Does it have vibration like it’s cavitation? If you can’t get it over 5-6k RPMs you probably won’t plane out, I have to run 7-8k to plane out. Check your air filters (clean with no oil) and oil level (make sure it’s not overfilled). And how old are your spark plugs?
HawaiiBreeze
Jetboaters Commander
- Messages
- 533
- Reaction score
- 845
- Points
- 187
- Location
- Oahu Hawaii
- Boat Make
- Yamaha
- Year
- 2017
- Boat Model
- SX
- Boat Length
- 19
I suppose by "blowing" you mean blowing up. If it's vibrating at that 5k-6k rpm it sure sounds like cavitation. Need to find the source...
Original post says "new everything"... is this the first time out since the new-everything? First things first start at the scoop grate looking for debris and work backwards to the "new everything" assembly. It sounds too easy but in the last week someone was asking why his battery wire was heating up and the boat wouldn't start...he posted pics and upon his review of his thread he noted he literally had his wires crossed on the terminals. Take your time and observe carefully.
Original post says "new everything"... is this the first time out since the new-everything? First things first start at the scoop grate looking for debris and work backwards to the "new everything" assembly. It sounds too easy but in the last week someone was asking why his battery wire was heating up and the boat wouldn't start...he posted pics and upon his review of his thread he noted he literally had his wires crossed on the terminals. Take your time and observe carefully.
- Messages
- 5,890
- Reaction score
- 6,662
- Points
- 492
- Location
- Corinth, TX (DFW)
- Boat Make
- Yamaha
- Year
- 2007
- Boat Model
- AR
- Boat Length
- 23
was there an issue that made you get new impellers and wear rings ?
did the boat run fine before the change ?
did the boat run fine before the change ?
- Messages
- 6,019
- Reaction score
- 5,463
- Points
- 462
- Location
- Florida
- Boat Make
- Yamaha
- Year
- 2021
- Boat Model
- Other
- Boat Length
- Other
you probably have air getting in someplace it only takes a little issue to cause cavitation, a bad seal around the pump or the clean out plugs
Similar threads
