peehole name?

[Skeeter456]

lol sooo what is the sx190's peehole name? Yesterday while washing my boat I snapped off the screw in gray elbow that comes out of it. Looking to buy another one but dont know the real name or where to look. Thanks

 

[Julian]

Probably part #12 in the attached link...but just guessing from your description:

2015 Yamaha SX190 (RX1800CP) Exhaust 3 | Yamaha Sports Plaza

 

[Skeeter456]

https://imgur.com/QjLSedh

 

[veedubtek]

Someone on here found some aluminum ones that fit and looked beautiful. I just can't seem to remember who at the moment...

 

[Skeeter456]

Its a piss poor made part. I was not even scrubbing hard and it went flying.

 

[veedubtek]

Found it!

https://jetboaters.net/threads/my-2016-fsh-sport-mods.11215/

Link to them in the first post there.

 

[veedubtek]

Actually, link dead. Found them here though--

https://www.ebay.com/itm/SILVER-Bil...391559629432?_trksid=p2385738.m4383.l4275.c10

 

[haknslash]

Your nut is fine. You need #12 if going back to stock.

You can get the aftermarket pissers here http://actionpowersports.net/product/ada-45-degree-billet-bilge-fitting/. A lot of the 192 guys have been running them since we upgrade the intercoolers and water lines. Cheaper than eBay

 

[Skeeter456]

Will those screw into my black nut already on the boat?

Edit: ahh i see its the whole setup! Thank you!!!! Now how about a better looking gas cap?

 

[haknslash]

Someone recently on the jetboaters FB page was also wanting to upgrade from the white cap to a metal one. One of the members said he bought a 2012 metal cap and an adapter. https://www.facebook.com/groups/jetboaters/permalink/1019811014839289/

 

[Ronnie]

FYI I see now that Yamaha calls the assembly a “Pilot Water Outlet” but I recall Jet Boat Pilot referring to it as a cooling outlet which is more descriptive in my opinion but being on this sight and YJB I’m still more familiar with the terms pisser or pee hole, but if this is correct shouldnt the part or assembly be called a d ch or penis?

 

[njmr2fan]

How about we group buy a bunch of them pisser- pee hole-cooling outlet thingies?

 

[FLBulldogger]

How about we group buy a bunch of them pisser- pee hole-cooling outlet thingies?

The link on the original post has moved I found some that are 3/4" and 45Degrees, just not sure without going out to the boat what the tubing width is...https://adaracing.com/personal-watercraft-products/fittings/jet-ski-bilge-outlet-fittings-45-degree/ I like these alot!

 

[haknslash]

I think the bilge is 3/4" and the pissers 1/2". @Rick Owens replaced all of his including the bilge so perhaps he will chime in. Several members have swapped theirs out and posting info in pics buried in @SamCF 's SX192 mod thread

 

[FLBulldogger]

I REALLY like this upgrade however I just went out and unscrewed the Pee Hole and tried to pull the hose and connectors out and no give in the line. Screwed the outlet back on and said ok how does one do this? I looked in the stern starboard holding space and could not trace either line the bilge or pee hole....Request an assist from you guys on the "how-to" on this one. Thanks

 

[haknslash]

The lines are the in the starboard storage. Have to stick your head way in there and look up and towards the rear/side.

 

[FLBulldogger]

Thanks @haknslash I knew I could count on you! I will take a look in the morning and see what I can see...

 

[haknslash]

Thanks @haknslash I knew I could count on you! I will take a look in the morning and see what I can see...

Here you go. Went out and snagged some pics for you. I'm pointing in the direction of the hoses. Once you stick your head in there you will see them. The fittings have nuts on the inside/backside, not just on the outside of the hull, so that's why yours weren't budging when you removed the outer nuts. If you look close you can see the nuts . The red line is what goes to the flush port adapter in case you're wondering.

 

[Seadeals]

Those are very cool. Now I have two more mods on the neverending list: peckers and a fancy sphincter (gas cap)! Both sound inappropriately appropriate given the bodily references. I like heap mods like this. You can fit them between the expensive mods to keep your mod “buzz” going.

 

[FLBulldogger]

Got them in this morning looks pretty cool. Install was relatively painless, except for using the dremel barrel sander to enlarge the pisser hole about a 1/16 of an inch....