Transom stereo dial replacement

[RNYCLV]

So over the summer at some point the dial that controls volume and settings either fell off or got swiped at some point. I have checked Partzilla, and some other OEM parts suppliers but cant find just the knob. I have sent two emails to the manufacture and have yet to get a reply. Anyone have an idea where I can find a replacement. I have been using needle nose plyers I had on board but it would be nice to have it correct again.

 

[Cleveland Steamer]

I lost mine about a year and a half ago and scored a replacement on eBay. I can see it in my order history but when I click on it I get redirected to knobs for other radios. I don’t think it’s available anymore from that seller.

 

[RNYCLV]

I lost mine about a year and a half ago and scored a replacement on eBay. I can see it in my order history but when I click on it I get redirected to knobs for other radios. I don’t think it’s available anymore from that seller.

Do you know what you searched under?
or how you searched to find it?

 

[Cleveland Steamer]

Do you know what you searched under?
or how you searched to find it?

I searched for ‘Polk PA4A volume knob’

https://a.co/d/aho7ubn

 

[Cleveland Steamer]

If it helps I can pull my knob off and measure it. Best I can do is use a tape measure and photo it.
When I search for the know I keep getting related products like the below. Most seem to be 32mm to 33mm so maybe that’s the size of the original knob? Maybe by measuring it will confirm it.

Amazon.com

 

[RNYCLV]

I searched for ‘Polk PA4A volume knob’

https://a.co/d/aho7ubn

Thank you, I keep searching for just polk audio volume knob and i get everything from sub woofer dials to home stereo equalizer dials... Its been frustrating

 

[RNYCLV]

If it helps I can pull my knob off and measure it. Best I can do is use a tape measure and photo it.
When I search for the know I keep getting related products like the below. Most seem to be 32mm to 33mm so maybe that’s the size of the original knob? Maybe by measuring it will confirm it.

Amazon.com

That would be awesome

 

[RNYCLV]

If it helps I can pull my knob off and measure it. Best I can do is use a tape measure and photo it.
When I search for the know I keep getting related products like the below. Most seem to be 32mm to 33mm so maybe that’s the size of the original knob? Maybe by measuring it will confirm it.

Amazon.com

I hate to ask, however were you able to get a measurement or that image?

 

[Big_O]

Did you ever find the replacement?

 

[RNYCLV]

Did you ever find the replacement?

No sadly I have not, I even talked with the dealership... OEM replacements are not the same. apparently for two years they used one size and then went to a bigger one because of this issue. I am going to get one that has a set screw and hope that it holds
That is unless you have one ....lol

 

[tdonoughue]

Whelp. Guess it is time to buy a new boat...

 

[Big_O]

? I’m actually having a metal plate made to cover the hole and mount a replacement remote PRC100 to replace the PA4A remote in that same spot.

 

[RNYCLV]

Whelp. Guess it is time to buy a new boat...

Sadly this is the new boat...lol

 

[RNYCLV]

? I’m actually having a metal plate made to cover the hole and mount a replacement remote PRC100 to replace the PA4A remote in that same spot.

Im going to have to figure something out, that seems like a good idea

 

[Julian]

I kept my eye out for a whole new PA4 and bought that on eBay a while back. Now when mine falls off I'm ready.

 

[RNYCLV]

S

I kept my eye out for a whole new PA4 and bought that on eBay a while back. Now when mine falls off I'm ready.

Smart man, I will have to start watching ebay for a whole new one just in cade anything else fails. I did buy one with a retention screw hoping that works.

 

[Cambo]

? I’m actually having a metal plate made to cover the hole and mount a replacement remote PRC100 to replace the PA4A remote in that same spot.

This post has a lot of great info about the remote relocating and covering the old hole

https://jetboaters.net/threads/wired-remote-for-factory-radio.16343/page-2

 

[RNYCLV]

This post has a lot of great info about the remote relocating and covering the old hole

https://jetboaters.net/threads/wired-remote-for-factory-radio.16343/page-2

Thank you

 

[Big_O]

? I’m actually having a metal plate made to cover the hole and mount a replacement remote PRC100 to replace the PA4A remote in that same spot.

Just got it today! Should be direct replacement to the PA4 remote. I’ll post some photos when installed.

Head Unit Replacement Faceplate

This is replacement faceplate for many Yamaha's with the OE Polk PA450. The main dimensions are 3.5" x 5.5" with a 2" cutout in the center. This is to remove the Polk PA450 Commander that is in the transom, and replace it with a metal plate that can cover that large hole, with thru holes to...

jewlscustoms.com